Welcome to the official website of NINGBO ZHENHAI TIANDI HYDRAULIC CO., LTD.!

Telephone

0574-86301550

news

Product Categories

Contact us

Contact:Cao jingshan

Phone:13586888865

Tel:0574-86301550

E-mail:cjs@nb-entiandi.com

No. 6007, zhenpu road, xiepu town, zhenhai district, Ningbo

The problem of heat and flow rate of forklift power unit is analyzed

Your current location: Home >> News >> Technical knowledge

The problem of heat and flow rate of forklift power unit is analyzed

Date of release:2019-06-16 Author: Click:

叉车动力单元

Many different situations may arise when using hydraulic power units, but here we focus on two common problems.The first case is that the temperature is very high and there are serious thermal problems.If you encounter this problem, we need to consider three aspects: first, it may be due to overloading of the system, that is to say, it exceeds its maximum capacity, mainly because the pressure is too high, or the speed is too fast

The second reason may be a problem with the hydraulic fluid used in the hydraulic power unit.For example, the cleanliness of hydraulic fluids may not be up to standard, leading to serious internal wear problems, resulting in reduced volumetric efficiency and leakage.The third reason is the temperature anomaly caused by the oil flow pipe being too thin and the oil flow rate being too high.

In the second case, the flow rate of the hydraulic power unit does not meet the standard, resulting in poor operation of the system and affecting the operation effect.These problems are mainly caused by four factors: 1.The cleanliness of the oil filter is insufficient, which affects the oil absorption;2. The installation position of the pump is too high;3. The suction pipe of gear pump is too thin.Influence oil absorption;4. Leakage of oil suction nozzle joint leads to insufficient oil absorption.

It should be noted that the temperature of the hydraulic fluid may increase somewhat during system operation.As the temperature increases, the viscosity may decrease.In order to ensure the normal operation of the hydraulic pump station, we need to control the oil temperature below 60°C.In addition, in the selection of hydraulic oil, we also need to consider the selection of hydraulic oil products at different temperatures can still maintain stability.Forklift power unit

The first condition for the proper operation of the hydraulic system is that the system must be kept clean inside, so the hydraulic system must be cleaned.The hydraulic system will inevitably be contaminated by external contamination before new equipment is run or after major repairs.The installation of hoses, pipes and fittings may introduce contaminants into the hydraulic system..Even new liquids can contain unexpected contaminants. Measures must be taken to filter out contaminants as quickly as possible, or they may fail soon after the equipment is put into operation.

Care should be taken during flushing:

(1) the tank should be closed to reduce the chances of particles from the air entering the tank;

(2) when flushing oil is added to the phase tank, a fuel cart with filter should be used to filter out the pollutants in the barrel oil;

(3) stop flushing the pump when replacing the filter element, and pay attention not to bring in impurities;

(4) regular exhaust and drainage should be carried out to ensure that the system is full and timely release of gases and pollutants.

(5) in the early stages of rinsing, evaporation of water in the oil is important.There should be a window for steam escape on the flushing tank.

(6) after flushing, pay attention to protection before pumping out the flushing oil and pipeline to prevent pollutants from entering the hydraulic system.

The power plant optimizes the product performance and establishes the "small but accurate" design concept in the structural design.Under the same performance conditions, minimize the use of products, such as using lightweight materials to remove excess functions and avoid excessive packaging, so as to reduce the weight of products.Focus on the hydraulic system design process of product diversification and serialization;Use reasonable technology to simplify the product processing process, reduce processing steps, simplify the disassembly process, such as easy disassembly connection method, reduce the amount of fastener, minimize the number of fastener in structural design to avoid destructive disassembly method, etc.Simplify product packaging as much as possible to avoid secondary pollution.



叉车动力单元


The address of this article:http://en.nbzh-tiandi.com/news/417.html

Key word:

Recently browse:

Related products:

Related news:

Contact information:

Contact:Cao jingshan

Phone:13586888865

Tel:0574-86301550

E-mail:cjs@nb-entiandi.com

Address:No. 6007, zhenpu road, xiepu town, zhenhai district, Ningbo


Quick link:

叉车动力单元

  • Service
  • Phone
    18270919270
  • Message
  • Website
  • Online Service
    Please leave a message for us
    Please input the message here, and we will contact you as soon as possible.
    name
    Contacts
    Telephone
    Telephone
    mailbox
    mailbox
    address
    address